<![CDATA[Unifi G3 Flex - was working, now not. [SOLVED]]]>I was an early adopter of this service. I added my local IP, no authentication, G3 flex cameras (seven) to the Portal and it all worked great.

Here lately I have been doing a review of all my devices and noticed this is no longer working.

Has there been a change to the Ubiquity pairing?

]]>https://forum.monoclecam.com/topic/482/unifi-g3-flex-was-working-now-not-solvedRSS for NodeMon, 11 May 2026 17:26:51 GMTThu, 23 Jan 2020 16:04:30 GMT60<![CDATA[Reply to Unifi G3 Flex - was working, now not. [SOLVED] on Fri, 24 Jan 2020 15:37:33 GMT]]>@cory_booth

Thanks for the guide and here is the link for future readers:

]]>https://forum.monoclecam.com/post/2111https://forum.monoclecam.com/post/2111Fri, 24 Jan 2020 15:37:33 GMT<![CDATA[Reply to Unifi G3 Flex - was working, now not. [SOLVED] on Thu, 23 Jan 2020 21:32:43 GMT]]>@Monocle
I posted my results to “General Discussion”
Success and very easy

]]>https://forum.monoclecam.com/post/2095https://forum.monoclecam.com/post/2095Thu, 23 Jan 2020 21:32:43 GMT<![CDATA[Reply to Unifi G3 Flex - was working, now not. [SOLVED] on Thu, 23 Jan 2020 16:33:21 GMT]]>@cory_booth

If your QNAP supports it, you could also probably run a full Ubuntu VM instance and install Monocle Gateway on it. The Docker option will use less resources but could be more tricky to setup.

Thanks, Robert

]]>https://forum.monoclecam.com/post/2091https://forum.monoclecam.com/post/2091Thu, 23 Jan 2020 16:33:21 GMT<![CDATA[Reply to Unifi G3 Flex - was working, now not. [SOLVED] on Thu, 23 Jan 2020 16:31:42 GMT]]>@cory_booth

Are you serious? What a backwards step…

Yes, and I agree. It all has to do with Amazon now enforcing that all camera connections use valid SSL certificates and a public DNS hostname … even for local/private network traffic. It’s very unfortunate.

I had Echo Spots and “upgraded” to Echo Show 8’s

Please also be aware that the “new” Echo Show 5 and 8 model will not display a camera stream with a resolution greater than 1080P. This is also unfortunate as most Alexa devices will happily display the stream and simply scale it on screen.

Man I hate running middleware - can the middleware run on QNAP?

I don’t have a QNAP to verify, but I would assume you can. I do run it in my house on a Synology NAS using a Docker instance.

QNAP has “Container Station” which loads Docker images.

Here are the instructions I use for the Synology:

Or you can just start with the plain docker container here:

Please read these pages carefully, the networking considerations are very important as the running container will need to be able to access your IP cameras and the Alexa devices must be able to access the container on port 443 from your private LAN:

I’ll be experimenting with this and let you know how it goes.

Please do and if you would be able to document the steps that would be very helpful for others.

Thanks, Robert

]]>https://forum.monoclecam.com/post/2090https://forum.monoclecam.com/post/2090Thu, 23 Jan 2020 16:31:42 GMT<![CDATA[Reply to Unifi G3 Flex - was working, now not. [SOLVED] on Thu, 23 Jan 2020 16:24:40 GMT]]>Oh ok - I just figured this out…

Are you serious? What a backwards step…

I had Echo Spots and “upgraded” to Echo Show 8’s

Man I hate running middleware - can the middleware run on QNAP?

QNAP has “Container Station” which loads Docker images.
I’ll be experimenting with this and let you know how it goes.

]]>https://forum.monoclecam.com/post/2088https://forum.monoclecam.com/post/2088Thu, 23 Jan 2020 16:24:40 GMT<![CDATA[Reply to Unifi G3 Flex - was working, now not. [SOLVED] on Thu, 23 Jan 2020 16:15:43 GMT]]>@cory_booth

Nothing had changed on our end. What Alexa device are you using? All of the newer Alexa devices now require using our Monocle Gateway software solution as well.

Thanks, Robert

]]>https://forum.monoclecam.com/post/2086https://forum.monoclecam.com/post/2086Thu, 23 Jan 2020 16:15:43 GMT