Monocle Gateway throws Proxy error at startup on Win2012R2 Server [SOLVED]

spicymikey

If I figure out the root cause I will post it here for you and others.

I actually don’t normally use the local IP. I just did that for testing. The goal is to be able to monitor the property from anywhere, not just inside the house.

I just made a $50 donation on your home page as a thanks for staying with me on this one. Thanks again!

Monocle

@spicymikey

Thank you for your generous support!

Here are some other threads on support for Monocle Gateway across multiple homes (remote locations)

If you want to access camera’s via Alexa from remote locations, basically, you will want to use the public IP you had mentioned and allow Monocle Gateway to host on port 443 on that public IP. See my previous post in this thread for more details.

Thanks, Robert

spicymikey

Hey Robert,

I have a followup issue I wanted to report. Maybe I should open another thread, but the camera fails to stream sometimes. it’s more than once in awhile. Pretty much 1 in 3. I can’t attach a text file. It says I don’t have enough privileges. I don’t want to just dump it in the post. Too much text but I have it here if you need it.

The only thing I can say is that when it fails, the “end point” throws a 401 and “unauthorized”. The debugger is showing the IP address of the Echo Show 5, but not certain if that is the endpoint throwing the error. See below

2019-07-27T16:24:20.675Z [DEBUG] [10.1.0.11:45270 <SyTnclcGH>] [ENDPOINT RESPONSE] <-- [401 (Unauthorized)] <cseq=1> (session=undefined)
2019-07-27T16:24:20.679Z [TRACE] [10.1.0.11:45270 <SyTnclcGH>] [ENDPOINT RESPONSE] <-- [HEADERS] {
“cseq”: “1”,
“date”: “Sat, Jul 27 2019 16:24:16 GMT”,

Monocle

@spicymikey

See if you can upload the log now. I adjusted some forum permissions.

Thank, Robert

spicymikey

@Monocle said in Monocle Gateway throws Proxy error at startup on Win2012R2 Server [SOLVED]:

@spicymikey

See if you can upload the log now. I adjusted some forum permissions.

Thank, Robert

Same error. “You do not have permissions for this action”

Monocle

@spicymikey

Well, the settings look correct … maybe try logging out then back in. I’m too familiar with the forum admin yet so it could still be an issue on my side.

Thanks, Robert

spicymikey

Here’s the log…

[0_1564258669283_EchoShow5_Reolink420_Success followed by failure.txt](Uploading 100%)

spicymikey

@Monocle
By the way, I think I understand what is happening, although not why it’s happening. The closing process is not resulting in a clean termination of everything. Maybe a connection is being left open, etc. The failures are occuring when I try to say “show camera” again right after closing it. Something i was doing a lot trying to test things. But if I wait 5 minutes, it seems to show the camera again reliably.

If this is a bug on the Amazon side then not much we can do about it, but if its a flaw in Monocle, hope that is a clue to help track it down.

Monocle

@spicymikey
I don’t think the upload made it. If it won’t work, then you could also use Pastebin, I have used that service before then just copy the link to the forum thread:
https://pastebin.com/

Thanks, Robert

Monocle

@spicymikey said in Monocle Gateway throws Proxy error at startup on Win2012R2 Server [SOLVED]:

@Monocle
By the way, I think I understand what is happening, although not why it’s happening. The closing process is not resulting in a clean termination of everything. Maybe a connection is being left open, etc. The failures are occuring when I try to say “show camera” again right after closing it. Something i was doing a lot trying to test things. But if I wait 5 minutes, it seems to show the camera again reliably.

If this is a bug on the Amazon side then not much we can do about it, but if its a flaw in Monocle, hope that is a clue to help track it down.

I have seen some camera’s behave this way. Are you using @tunnel or @proxy for this camera? @proxy will try to leave the connection open for a few minutes just in case a new request comes in for the stream.

Thanks, Robert

spicymikey

@Monocle
I’ve tried it with @proxy-tcp, and without it. I’m ALWAYS using @tunnel per the documentation on the website. I can mess around with different combos and see what happens

Monocle

@spicymikey

If using one of the @proxy tags, then you can also combine that with @hangup to forcefully disconnect immediately with the Alexa device disconnects the TCP socket. However, @hangup has no impact on @tunnel connections.

I noticed on another thread you mentioned this was a Reolink camera. I have seen that behavior before on Reolink cameras. It could simply be some bug or issue with the camera itself. But yes, it only manifests when making back to back connections and seems to work fine under normal use when your only periodically ask for the stream.

Thanks, Robert

spicymikey

@Monocle said in Monocle Gateway throws Proxy error at startup on Win2012R2 Server [SOLVED]:

@spicymikey

If using one of the @proxy tags, then you can also combine that with @hangup to forcefully disconnect immediately with the Alexa device disconnects the TCP socket. However, @hangup has no impact on @tunnel connections.

I noticed on another thread you mentioned this was a Reolink camera. I have seen that behavior before on Reolink cameras. It could simply be some bug or issue with the camera itself. But yes, it only manifests when making back to back connections and seems to work fine under normal use when your only periodically ask for the stream.

Thanks, Robert

Thanks for the advice. I think adding the @hangup solved it. Is that documented anywhere? First I’ve heard about @hangup, but I may have missed it.

For me with the Echo Show 5, a Reolink RLC420, and the Monocle Gateway, changing to these tags worked to eliminate the problem. A few combinations worked, but the most minimalistic combo is what I will stay with

FROM: @ntpnow, @tunnel, @proxy-tcp

TO: @hangup, @proxy

Monocle

@spicymikey

RE: @ntpnow, @tunnel, @proxy-tcp
You can only use one of these at a time: @tunnel, @proxy or @proxy-tcp. If you include multiple, I think @tunnel will win and other will be ignored.

FYI:
If your camera manufacture is set to “Reolink” then @ntpnow is not needed. We shove that tag at runtime automatically for Reolinks as they all seem to require it.

Is that documented anywhere? First I’ve heard about @hangup, but I may have missed it.

@hangup may not be documented yet, its one of the newer tags and only used in a handful of cases.

Thanks, Robert

spicymikey

Thanks Robert. I have been testing it on and off for 30 minutes and its working like a charm. I know I thought this yesterday, but I think we got this now. If I discover anything else I’ll post something

Sasq

For anyone else having the same Proxy Error starting on Windows Servers, i found that 443 was also being used by IIS. Stopping and disabling the “World Wide Web Publishing Service” service freed the port and allowed monocle gateway to run. Appreciate this may not be an option for everyone.